How to remove printhead from kodak printer

how to remove printhead from kodak printer

KODAK ESP 3.2 and 3.2s All-in-One Printers — Extended User Guide

To replace the printhead: Make sure your printer is on. Lift the printer access door, and wait for the carriage to move to the access position. Remove both ink cartridges and set them aside. Unlatch the used printhead by lifting the button in the center of the carriage. Lift the used printhead out of the carriage. Remove the new printhead from its bag. Lift the access door, and wait for the carriage to move to the access position. Remove both ink cartridges and set them aside. Unlatch the used printhead by lifting the button in the center of the carriage. Lift the used printhead out of the carriage. Remove the new printhead from its bag.

The printhead may need to be aligned to enable high-quality prints. The Kodak printer automatically performs a calibration every time you install or replace a printhead. You can also initiate a printhead alignment from the ESP 3 printer driver, Home Center software, or control panel.

The following pattern is printed and calibration is complete when the page is printed. Run a printhead cleaning if color is faded or missing by pressing and holding Copy and Cancel at the same time.

Pinch the latch on the ink cartridge with your thumb and forefinger and lift it out of the print head. Remove both ink cartridges. Printhead Alignment The printhead may need to be aligned to enable high-quality prints. To align the printhead from the control panel Load the paper tray with US letter or A4 Kodak plain paper. Clean Printhead Run a printhead cleaning if color is faded or missing by pressing and holding Copy and Cancel at the same time. Replace the Printhead If your printhead is damaged or broken it is easy to replace yourself.

Open the printer access door. Unlatch the printhead by pressing the release on the top of the carriage. Remove the old printhead from the carriage. Remove the new printhead from its bag. Remove and discard the black plastic casing and the orange protective cap. How to erect a retaining wall the new printhead into the carriage.

Push firmly against the target label on the printhead until you hear it click into place. Re install the ink cartridges. Close the printer access how to remove printhead from kodak printer. Previous Next.

Make sure the printer is on. Lift the access door, and wait for the carriage to move to the access position. Remove both ink cartridges and set them aside. Unlatch the existing printhead by lifting the button. Lift the used printhead out of the carriage. Remove the new printhead from its bag. To replace the printhead: Make sure your printer is on. Lift the printer access door, and wait for the carriage to move to the access position. Remove any paper that may be loaded in the printer. Remove both ink cartridges and set them aside. Unlatch the used printhead by lifting the button in . Make sure your printer is on. Lift the access door, and wait for the carriage to move to the access position. Remove both ink cartridges and set them aside. Unlatch the printhead by pushing the button in the center of the carriage. Lift the printhead out of the carriage. Remove the new printhead from its .

The printer detects the new printhead. Follow the instructions on the LCD to calibrate your printer. Replace the printhead only if you receive a new printhead from Kodak.

To replace the printhead: Make sure your printer is on. Lift the printer access door, and wait for the carriage to move to the access position. Remove any paper that may be loaded in the printer. Remove both ink cartridges and set them aside. Unlatch the used printhead by lifting the button in the center of the carriage. Lift the used printhead out of the carriage. Remove the new printhead from its bag. Remove the two plastic protective shields. Place the new printhead into the carriage.

Insert it at the angle shown. Push firmly against the target label of the printhead until you hear a loud snap. Insert the black ink cartridge into the printhead. Press down on the ink cartridge until you hear it click into position.

Repeats steps 11 - 12 for the color ink cartridge. Close the printer access door. Previous Next. Replacing the printhead is not a regular maintenance procedure.

3 thoughts on “How to remove printhead from kodak printer

Add a comment

Your email will not be published. Required fields are marked *