How to plumb a bathroom sink

how to plumb a bathroom sink

Installing Bathroom Sink Plumbing

Feb 25, †Ј The bathroom sinkТs water lines are roughed-in 3 inches above the drain. Measure 21 inches (approximately) above the finished floor. The hot line and cold line are spaced 8 inches apart (from left to right). From the center of the drain, . Sep 19, †Ј Bathroom Sink Plumbing Diagram The sink drain has a flange that is sealed to the sink hole with plumberТs putty. This flange is screwed into the drain body, which is tightened to the underside of the sink bowl with a locknut. Find Pre-Screened Plumbers Near You.

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.

Installing a new sink can be a beautiful addition to any bathroom, kitchen, mudroom, laundry room, and more. However, if it is not installed properly, or if it is not installed using the proper steps, it can quickly turn your project into a hassle.

Therefore, before installing a new sink, there are few expert tips to consider in order to help ensure your project runs smoothly and the sink works efficiently.

When installing a new sink, there is a common misconception that the sink can be installed before the piping, and then simply run the piping through the floor to the existing pipe system. However, this is simply not true because sinks not only require drain pipes, which slope downward and into the stack, but they also require vent pipes, which extend upward and join the stack higher on the line, usually in the attic.

Before you begin your pipework, you need to open the wall from the crawl space up to the attic. Once the wall is open, simply tie the new pipes into the existing drain system in the crawlspace, and then run them up to the sink area, and then to the attic where they will tie into the vent piping system. Be sure to apply a thread lubricant on all how to plumb a bathroom sink to fill the gap between the thread joints to help make them pressure proof and leak proof.

You should also be sure to add drain clean-outs where applicable to help make it easier to clear clogs. Though you can use sturdy copper pipes or even CPVC pipes to connect to the main water line in the crawl space, PEX piping, which many professional plumbers often prefer, helps how to plumb a bathroom sink your job a bit easier because it is flexible and great for long runs.

It is also less expensive and easier to fit than both copper and CPVC pipes. When using PEX piping, be sure to fit the main water pipes with PEX adapters, and then solder them before connecting the flex tubes to the adapters for a sturdier fit.

Connect the handles and the faucet to the sink. Afterward, run the PEX pipes to the sink handles using hard lateral rises, which are available in chrome and copper. Secure the hard lateral rises to the handles with nuts. Be sure to secure the base of the PEX pipes with grommet rings. Though plastic drain pipes, such as polyvinyl chloride PVC and polyethylene PEare a common choice for many plumbing projects due to their low cost, many professional plumbers recommend using metal pipes when possible because they are more durable and last a long time.

Assemble the top half of the drain pipe system together, and use adhesive on all threads to help secure it. Finally, connect the remaining drain pipes, what helps concentrate for studying the P-trap, to the sink to complete the installation. Applying a sealant, how to plumb a bathroom sink as pipe dope or Teflon tape, to all threaded plumbing connections helps provide a watertight seal, so keep this in mind when connecting and installing the drain pipes.

Should you choose to run copper lines or tie into copper lines for your project, be sure to use lead-free solder for any water that may enter the body.

When soldering joints, consider using a soldering flux on pipe fittings. It helps ensure the solder gets way down into the fitting as opposed to just remaining on the surface. This helps ensure the joints are filled with solder and properly fitted to prevent leaky joints.

Once the sink is properly plumbed and installed, turn the water how to plumb a bathroom sink on, and inspect the sink area for leaks. Turn on the faucet, and fill the sink with water. If it is a bathroom sink, allow the water to fill past the overflow to be sure the overflow is properly draining. Next, inspect the floor near the hot and cold water lines to be sure there are no leaks. Inspect the drain pipes and all other attachments for signs of leaking.

Lastly, allow the water to drain from the sink to be sure the sink is draining properly. It should drain pretty quickly. To maintain your new sink, keep the drain clean, and have a sink plunger on hand to address clogs.

Overall, how to plumb a sink is pretty straightforward provided you have some understanding before beginning your project. These tips on how to plumb a sink are expert tips that can help you get the most out of your sink installation. If you have used these tips on how to plumb a sink and have found them useful, or if you have experience with how to plumb a sink and would like to share your how to start a checking account with others, then feel free to share your knowledge.

Image Source : DepositPhotos. Your email address will not be published. We may also earn commissions on how to make grilled cheese sandwhich from other retail websites. Do: Open the Wall from the Crawl Space to the Attic Before you begin your pipework, you need to open the wall from the crawl space up to the attic. Submit a Comment Cancel reply Your email address will not be published. Search This Site Search for:.

Menu Home Troubleshooting. Pin It on Pinterest.

Related Articles

Installation of bathroom sink plumbing proceeds in two phases. The first is the rough-in, when you install all the water, drain and vent pipes in the walls and leave them stubbing out at the sink. Jun 24, †Ј This video shares how to install PEX pipe in bathrooms instead of soldering copper. We do a tool overview and show tips for proper dattrme.coml Links.

Installation of bathroom sink plumbing proceeds in two phases. The first is the rough-in, when you install all the water, drain and vent pipes in the walls and leave them stubbing out at the sink location.

In the second, or finishing, phase, you hook the sink and faucet to the stub-outs. The rough-in phase is the one that requires the most plumbing know-how. If it's done properly, finishing should be problem-free.

The supply, drain and vent pipes for the sink tie into the system of pipes already servicing your bathroom, and the difficulty of the rough-in depends on the system's overall configuration. Similarly, you can usually tie the 2-inch drain line into an existing one. It's important to remember to vent the sink, or it won't drain properly. The locations of the supply and drain stub-outs are important.

The drain should be lined up with the sink drain and centered between the supply stub outs. You have to uncover the wall to run the pipes through it, and the water must be off when you solder the tees onto the pipes from which you're drawing the supply. Allow the stub-outs to extend a few inches from the wall and cap them until you're ready to install the sink. Before you hook up the sink, you need to install shutoff valves on the supply stub-outs.

After cutting off the caps with a pipe cutter, you can either solder slip-joint valves to the pipes or tighten on compression valves with a wrench. If you used CPVC plastic pipes instead of copper ones, you also have the option of gluing on the valves. It's always easier to preinstall the faucet and drain onto a sink before installing the sink so you don't have to do these procedures while lying on your back.

The pipe that extends down from the drain is called the tailpiece, and it should end at the same level as the top of the drain so that the trap connects easily. The faucet supply hoses connect to the shutoff valves and faucet inlets, and you tighten them with adjustable pliers.

They must have the right size connectors to fit, so it's worth checking before you buy the hoses. After connecting the pop-up stopper, the sink should be ready to use. Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since As a landscape builder, he helped establish two gardening companies.

By Chris Deziel. Related Articles. Overview The supply, drain and vent pipes for the sink tie into the system of pipes already servicing your bathroom, and the difficulty of the rough-in depends on the system's overall configuration. Installing the Pipes The locations of the supply and drain stub-outs are important. Preparing the Stub-Outs Before you hook up the sink, you need to install shutoff valves on the supply stub-outs.

Connecting the Sink It's always easier to preinstall the faucet and drain onto a sink before installing the sink so you don't have to do these procedures while lying on your back. References Dr.

2 thoughts on “How to plumb a bathroom sink

Add a comment

Your email will not be published. Required fields are marked *