How to notch corner deck post

how to notch corner deck post

How to Install Deck Railing Posts

May 25,  · Notching a deck post for the double 2 x 10 The load for the deck is transferred down through the post to the footings and the upright notched section of the. Apr 10,  · dattrme.com founder, Tim Carter, shows why a notched post is better than bolting a beam to a dattrme.com more DIY Shed building tips and inform.

Remember Me? What's New? Results 1 to 5 of 5. Thread: How to notch a outside 90 degree corner post for a deck railing. Join Date May Posts How to notch a outside 90 degree corner post for a deck railing I have searched this forum and YouTube for a hand rail corner post notch method. I saw many demos on cutting the hand railing notch that goes down the front and sides. Nothing on the corner post on a 90 degree outside corner.

I can use my TS to make the long cuts, but how can I notch the part of the cut that sets down on the top of the deck. I am replacing all my hand railing post and when looking at the old corner I cant tell how the original builder made the cut.

My best guess is to use the TS and then chisel out the corner. Please help Thanks Johnny. Google Sponsor Google Sponsor. Skip the tablesaw, first off.

Mark out where the two how to fold a quillow into a pillow cuts will be. Set the circular saw to that depth. You can add the guide of your choice, mine was a bit simple IMAG A little over cut is ok. Then, turn and clamp the post so that the "point" is up.

Cut straight across at the top of the joint. Then just pop out the waste, and a chisel to clean up. Now, IF you are talking about making a notch on the outside of a post, welllllll, think LOTS of kerf cuts, knock out the waste with a hammer, then a how to notch corner deck post chisel to clean then up.

Thanks Guys Steven I'll try your method. Thanks for the help Johnny. Yep - until I saw it done, I would have struggled with figuring out the corner notch. Like the man said - set the depth of a circular saw, make lots of kerf cuts, how to install dth at home knock out the waste. The guy I saw used the same circular saw to clean up the stubble, but a chisel would work with a little more "elbow grease".

Join Date Nov Posts Just a FYI, notched 4x4 posts are no longer code in most of the country for guardrails due to strength concerns. Check out the IBC deck companion for more info on best how to notch corner deck post. If you are using 6x6 posts the above works for long runs, with an outside corner you are better off how to frame stained glass panel two posts at the outside of each end separated by a short section.

Don't try to copy your old builders construction methods, they could be dangerous. Sponsored Forums Private Forums Authors. All times are GMT The time now is PM. All rights reserved.

Installation

Jun 26,  · Cut straight across at the top of the joint. Then just pop out the waste, and a chisel to clean up. Now, IF you are talking about making a notch on the outside of a post, welllllll, think LOTS of kerf cuts, knock out the waste with a hammer, then a wide chisel to clean then up. BTDT. Cut the 6?6 deck post to length and mark the notches. Set the saw to the depth of the notch as shown and make both crosscuts. Then reset the blade to maximum depth and make the four rip cuts. Mark the posts for a notch that is /2 inches deep and as long as the depth of the joist—about /2 inches for a 2x8 joist, about /2 inches for a 2x (Use a joist scrap to be exact.) Add the thickness of the decking and mark for the crosscut. Cut the notch Make a crosscut where the notch ends.

The first step in adding the railing to the deck is installing the posts. We'll show you how to do it in five simple steps. A railing is one of the most visible parts of a deck, but it's also a key safety feature. When planning out railing posts, it's important to keep both factors in mind.

Choose lumber, for example, that is free of cracks and splinters. After the railing is installed, sand all the corners smooth. Before you begin, draw your design and double-check the sizes and measurements. In our railing the post length equals the height of the railing above the deck plus the decking thickness, plus the joist width, minus the thickness of the cap rail.

The baluster length equals the height of the railing above the deck minus the gap between the bottom of the railing and the deck about 2 to 3 inches , minus the thickness of the cap rail. Also make sure to check local codes and include any requirements in your plan.

Some common considerations include:. Creative Deck Railing Ideas. Posts are as long as the height of the railing, plus the width of the joist and the thickness of the decking, minus the thickness of the rail cap.

Set up a jig that allows you to cut all the posts to the correct length. Drill holes the same diameter as the carriage bolts you will use. Staggering the holes avoids splitting the post along the grain lines. For each post cut a notch in the decking so the post can fit tightly against the joist. Use a professional-quality jigsaw for this—it's difficult to cut straight with a cheap model.

Clamp the post so it is plumb in both directions. Drill into the existing holes and through the joist. Tap carriage bolts all the way through. Under the deck, slip on a washer and tighten a nut for each bolt. Where the railing meets the house, use 5-inch lag screws and washers to firmly fasten a 2x4. This is stronger than a 4x4 post attached to the deck. Notched posts take time and experience to cut, but make a pleasing finishing touch for a deck railing.

They draw the baluster up closer to the deck edge and make a slightly firmer joint than surface-mounted posts. Use a joist scrap to be exact. Add the thickness of the decking and mark for the crosscut. Cut the notch Make a crosscut where the notch ends. With the saw set to maximum depth, cut the long lines on each side without cutting beyond the crosscut. Chisel away the excess Use a hammer and chisel to crack out the waste—it will neatly pop out as one piece.

Then chisel away the remnant where the saw blade could not reach. Complete the corner post Make the long cuts and a shallow crosscut. Chisel toward the crosscut and split out the waste. Chisel down along the crosscut and along the long cuts to remove the remnant of wood remaining.

How to Install Deck Railing Posts. January 26, Save Pin FB ellipsis More. The minimum height of the railing. Allowable baluster spacing. How the posts attach to the framing. The maximum space between the bottom of the balusters and the deck. Comments Add Comment. Share options. Back to story Comment on this project Rate Review Comment on this story. Tell us what you think Thanks for adding your feedback. Close Login. All rights reserved. View image.

5 thoughts on “How to notch corner deck post

Add a comment

Your email will not be published. Required fields are marked *